Last updated:

The house cools down fast, the system shuts off, and twenty minutes later the rooms feel sticky again. Now the old heat pump is wearing out too, and you don’t want to buy the same problem twice.

Sweet Olive installs and replaces ducted air-source heat pumps in Harvey and across our service area. In Harvey the permit goes to Jefferson Parish, and the bigger question is usually size: a unit matched to the old nameplate can repeat the same short, damp cycles. So on the first visit we measure the rooms, check where the air handler draws its return and test the ducts. Your written estimate names the equipment, its capacity, any sealing and the parish permit steps.

If the system still has years left, a repair or an inspection may be the right first step. When it is done, the replacement page covers the decision in full.

What a humidity-first replacement in Harvey looks like

A big system that cooled fast, a house that still felt clammy and an air handler in the garage: why this Harvey replacement went smaller and sealed the return.

Old garage air handler with a taped, leaking return plenum in Harvey
Before
New garage air handler on its platform with a rebuilt sheet-metal return plenum sealed in mastic
After
Location
Harvey, off Manhattan Boulevard
Home
Single-story slab house with an attached garage, about 1,600 sq ft, three bedrooms
System
Nominal 2.5-ton variable-capacity matched system, down from a 4-ton nameplate
Old system
4-ton single-stage, short cycling
Air handler
Garage platform; return plenum rebuilt and sealed
Line set
20 feet, new, sized to the new equipment
Project price
$9,850
Duration
2 working days

The problem

Cold air, damp rooms

The house was a single-story slab home off Manhattan Boulevard in Harvey, about 1,600 square feet with three bedrooms. Its four-ton heat pump was wearing out, and even in good years it had run in short, loud bursts: the thermostat hit 74 and the rooms still felt clammy, with a musty smell in the closets. The air handler stood on a platform in the attached garage.

The finding

Too big, and breathing garage air

The room-by-room load calculation supported a nominal two-and-a-half-ton system, well under the old nameplate, which explained the short runs. The supply ducts tested sound, but the return plenum beside the air handler leaked at every seam and pulled warm, damp garage air into the system. Matching the old size was the cheaper option, and a standalone dehumidifier was another; neither fixed why the house stayed damp.

Startup recordPressure test heldMicron gauge: dryCharge weighed inAirflow and staticDrain and float switchStages and backup heat
The startup record left with the house: pressure test, evacuation, charge, airflow and static pressure, the drain and float switch, and the thermostat and backup heat.

The work

Smaller equipment, a sealed return

We chose a variable-capacity system built to run long and slow on muggy days. On day one we recovered the refrigerant, removed both old units and rebuilt the return plenum in sheet metal with every seam sealed in mastic and a gasketed filter door, then set the new air handler on the platform with a float switch on its drain. On day two we set the outdoor unit and ran a new 20-foot line set sized to the new equipment, brazed under nitrogen, pressure-tested and evacuated.

The handover

Blower set for moisture, not just cold

We weighed in the charge, measured airflow and static pressure, and set the blower and thermostat for moisture removal at low speed instead of a race to the setpoint. The readings stayed with the owner, and the Jefferson Parish inspection followed. The aim was a house that felt dry at the temperature it was set to.

Cold air but damp rooms: is it the size?

A system that cools fast isn't always a system that dries the air.

Connected front rooms of a New Orleans shotgun double with ceiling supply registers
Connected front rooms share one load, so sizing starts with each room that feeds it.

Short cycles leave water behind

A heat pump dries the air while its indoor coil stays cold and wet long enough for water to drip off. Oversized equipment hits the thermostat setting in a few minutes and shuts off before that happens, so the house reaches 74 and still feels clammy. We run a room-by-room load calculation (ACCA Manual J) and size from it, because matching the old nameplate only repeats whatever sizing the house got last time. Our sizing guide explains the method.

Damp has more than one cause

Leaky return ducts, a blower set too fast for a humid climate or a low refrigerant charge can each leave the air wet, even on a correctly sized system. We measure before naming a cause, and the humidity guide walks through the signs.

Single-stage

Runs at full output or not at all.

  • Lower equipment cost
  • Works with simpler thermostats
  • Needs close sizing to dry the air

Variable-capacity

Runs low most of the time and steps up on the hottest afternoons.

  • Long, slow runs that remove more moisture
  • Higher equipment cost
  • Needs a matching thermostat

In a house that has always felt damp, the longer runs of variable-capacity equipment are often worth pricing next to single-stage.

A heat pump thermostat on the plaster hallway wall of a New Orleans house
A thermostat that can run each stage and the humidity setting the equipment offers.

Air handlers in garages, closets and attics

Where the indoor unit sits changes what we check on the first visit.

In the garage

An air handler on a garage platform works well if its return draws only from the house. Where the return plenum or filter door leaks, the system pulls in garage air with its heat, moisture and dust. We check every seam and price sealing or a rebuilt plenum as its own line.

In a closet or the attic

A hall closet keeps the unit inside the cooled space, with the return beside it. An attic unit above a finished ceiling gets a secondary drain pan and a float switch, so a blocked drain shuts the system off instead of staining the ceiling. Either way, the ducts are tested for leakage and static pressure before we plan to reuse them; failing runs go into a ductwork repair line.

New horizontal air handler on a platform seen from the pull-down stair of a Timberlane attic
An air handler with its return and drain connections in reach, the first things we look at.

Permits and where Harvey sits

Harvey is unincorporated, between the City of Gretna and Marrero.

A parish filing

Harvey has no city government of its own, so heating and cooling equipment is filed with the Jefferson Parish Building Regulatory Division before the work, and an inspection follows. Gretna to the east runs its own Building Department, so an address close to that line gets checked first. Marrero to the west and Woodmere to the southwest stay with the parish. The permit guide compares the offices. We also confirm which electric utility serves your account, since that decides which rebate programs could apply; the rebate guide explains why.

Water around the outdoor pad

Heavy summer rain can stand in West Bank yards for a while. Heating and cooling equipment isn’t built to sit in water, so we look at where it collects on your lot and check the parcel’s requirement before keeping the old pad or choosing a stand.

What a Harvey replacement costs

Capacity, equipment tier and the return usually decide where a Harvey house lands.

Sweet Olive's typical range for a residential ducted heat pump replacement is $4,250 to $11,750. We set your price after the site visit and write it into your estimate line by line, including the Jefferson Parish permit steps for your address.

What moves a Harvey price

  • Capacity and tier. Single-stage, two-stage or variable-capacity, sized from the load calculation.
  • The return and ducts. Sealing a plenum, rebuilding one, or repairing failing runs.
  • Electrical work. Reusing a sound circuit or adding one, with a panel upgrade as a separate line.
  • Controls. A thermostat that matches the equipment and its humidity setting.
  • The outdoor spot. Line-set length, and a pad or stand on low ground.

The cost guide breaks a price into its parts, and the stage comparison explains what the extra cost of variable capacity buys.