# Heat Pump Cost Estimator for New Orleans Homes

> Answer seven questions about your New Orleans house and see where a ducted heat pump job sits in our typical range, with each price driver on its own line.

URL: https://sweetolivenolaheatpumps.com/tools/heat-pump-cost-estimator/

Seven questions about the house, and you see where a job like yours sits in our typical range, with each thing that moves the price on a line of its own. No contact details needed.

Estimate pages and a highlighter on a kitchen table in a New Orleans home.

[Sweet Olive](https://sweetolivenolaheatpumps.com/) installs and replaces ducted heat pumps across New Orleans. Before anyone visits, you want a sense of what the job will cost, and our typical range for a whole-house job, $4,250 to $11,750, is a wide place to start. This planner narrows it: tell it what is in the house now, what shape the ducts are in, what the panel and the access look like and which equipment you're leaning toward.

It answers with our typical range for your kind of job, the part of that range your answers point to, a line for each driver, and any work that belongs on a line of its own. It also points you to typical [replacement](https://sweetolivenolaheatpumps.com/heat-pump-replacement/) and [installation](https://sweetolivenolaheatpumps.com/heat-pump-installation/) jobs on our pages with scopes like yours, and what each is priced at.

The figure for your house still comes from the visit. We measure the rooms for a [load calculation](https://sweetolivenolaheatpumps.com/guide/heat-pump-sizing/), test the ducts, look at the panel and the outdoor spot, and write the estimate line by line. The [cost guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-cost/) explains each line, and the [other free tool](https://sweetolivenolaheatpumps.com/tools/) sorts out comfort problems before a visit.

## Build your planning budget

Every answer updates the result straight away. Change anything you're unsure of and watch which lines move.

Your planning budget

### Sweet Olive's typical range for a residential ducted heat pump replacement is $4,250 to $11,750.

Lower end Middle Higher end

Your answers sit in the middle of the range. Plan your budget around the middle of the range. Some of what you describe pushes the price up and some keeps it down.

#### What moves it

- No push either way Replacement: the old system's refrigerant is recovered and the equipment hauled away, as a line inside the range.
- No push either way A mid-size house: size alone doesn't move the price much.
- No push either way Ducts to be tested at the visit: their result can move the price either way.
- No push either way Panel and circuits checked on the first visit.
- No push either way No hard access: an open side yard, an existing pad and room to work.
- No push either way Equipment tier still open: we compare tiers side by side on the estimate.

#### Permit, rebates and running cost

- City of New Orleans Safety and Permits issues the mechanical permit. The fee depends on the components in the job.
- Energy Smart NOLA lists a rebate of $200 to $250 for qualifying equipment installed by a participating contractor, for Entergy New Orleans residential accounts, within the program's current funding period. It isn't counted in the range; whether it applies depends on your account and the equipment.
- The federal 25C tax credit no longer applies to equipment placed in service after December 31, 2025, according to IRS guidance.
- What the system costs to run depends on your rate schedule, the equipment tier and how tight the house is. We compare tiers on the estimate rather than promise a bill.

#### Typical jobs like this on our pages

- [A replacement in Metairie, Jefferson Parish](https://sweetolivenolaheatpumps.com/service-areas/metairie/) $7,850 · 2 working days
- [A replacement in River Ridge, near Jefferson Highway](https://sweetolivenolaheatpumps.com/service-areas/river-ridge/) $7,950 · 2 working days

This is a planning budget, not a quote. We set your price after the site visit and write it into your estimate line by line.

## How the planner reads your answers

Each answer pushes the budget toward the lower end, toward the higher end, or neither way. The pushes are added up, and the total picks the lower end, the middle or the higher end of our range.

The planner doesn't multiply anything by your floor area or produce a figure between the two ends of the range. Floor area, ducts and access only say which way a job leans; the size of the step comes from the visit. Work that sits outside a whole-house job, like a panel upgrade or a second system, goes on a separate line with no figure, because we price it from what the visit finds.

### The job and the house

| Your answer | Effect | Why it moves the price |
| --- | --- | --- |
| What is in the house now? |  |  |
| A heat pump, or central air with electric heat, to replace | No push either way | A replacement keeps the parts of the house that test sound, so the job itself doesn't push the price either way. Removal is a line on every replacement estimate. |
| Central air with a gas furnace, to switch to a heat pump | No push either way | A conversion replaces two pieces of equipment with one matched system. The gas capping and flue work add steps, and the furnace no longer needs its own service, so on balance it sits with replacements. |
| No central system yet: window or wall units, or nothing | Toward the higher end | A first system has nothing to reuse. Even before the ducts, the air handler location, drain, circuits and outdoor spot are all new. |
| About how big is the conditioned part of the house? |  |  |
| Under 1,300 sq ft | Toward the lower end | A smaller load means smaller equipment, a shorter list of supply runs and less attic time. |
| 1,300 to 1,800 sq ft | No push either way | In this band the ducts, the panel and the access decide more than the floor area does. |
| 1,800 to 2,500 sq ft | Toward the higher end | A bigger load means bigger equipment and more supply runs and returns to build or test. |
| Over 2,500 sq ft, or two floors | Toward the higher end, plus a separate line | Above about 2,500 square feet, or across two floors, one system can struggle to reach every room evenly. When the load calculation calls for two, each is priced as its own system. |
| What shape are the ducts in? |  |  |
| Cool air reaches every room and the ducts look sound | Toward the lower end | Sound ducts are the largest saving available on a replacement: tested, resealed where needed and reused. |
| Ducts are there, but some rooms run hot or the runs are old | No push either way | Targeted duct work adds a day or part of one, but most of the system stays, so it lands between reuse and a new duct system. |
| No ducts, or ducts that need replacing | Toward the higher end | A whole duct system is priced by the house: every run, the plenum, the return and the attic or crawlspace time to build them. |
| Not sure | No push either way | Until the ducts are tested, the planner doesn't push the price either way. The test result can decide where your house lands. |

How each answer about the job and the house moves the planning budget, and why.

### Wiring, access and equipment

| Your answer | Effect | Why it moves the price |
| --- | --- | --- |
| What do you know about the electrical side? |  |  |
| Replacing a system on circuits that already suit it | Toward the lower end | When the old circuits, breakers and disconnect match the new equipment, the electrical line stays short. |
| New circuits needed, and the panel has room | Toward the higher end | New 240-volt circuits for the outdoor unit and the air handler's heat strip, plus a disconnect, add labor and materials inside the range. |
| An older or full panel that may need an upgrade | Toward the higher end, plus a separate line | Circuits for the new system are inside the range. A panel upgrade is a different job, so it sits on its own line of the estimate. |
| Not sure | No push either way | Until we see the panel, the planner doesn't push the price either way. |
| Which of these describe the house? Pick any that apply. |  |  |
| The air handler goes in the attic | Toward the higher end | An attic air handler needs a platform, a secondary pan and a float switch so a blocked drain can't stain a ceiling, and the work is slower in a hot attic. |
| Ducts or equipment under a raised floor | Toward the higher end | Low headroom under a raised house slows every duct connection. |
| A narrow side gate or tight side yard | Toward the higher end | Equipment that can't be wheeled in takes more hands and more time to place. |
| A raised stand for the outdoor unit, on a low lot or beside a raised house | Toward the higher end | A stand costs more than a pad and takes longer to set and anchor. Flood elevation is set parcel by parcel, so the height is checked for your lot. |
| A local historic district, with the unit visible from the street | Toward the higher end | In a local historic district, ground equipment belongs in the rear or side yard and visible equipment is screened, which can mean a longer line set and a review step. |
| A new spot for the outdoor unit, or a long run for the copper lines | Toward the higher end | Every extra foot of line set adds copper, insulation, brazing and sometimes a wall cover. |
| None of the access conditions | No push either way | With easy access the planner doesn't push the price either way. |
| Which kind of equipment are you leaning toward? |  |  |
| Single-stage | Toward the lower end | Single-stage equipment runs at full output or off, and it costs the least to buy. |
| Two-stage | No push either way | Two-stage equipment sits between the other two in equipment cost. |
| Variable-speed | Toward the higher end | Variable-speed equipment and its controls cost the most to buy. |
| Not sure yet | No push either way | Until you choose, the planner doesn't push the price either way. |

How each answer about wiring, access and equipment moves the planning budget, and why.

Access answers count together but can push the budget only so far, because a hard attic and a tight gate on the same house share some of the same extra time.

## Our typical range, and how your price is set

The planner always works inside the range we publish for your kind of job.

**Sweet Olive's typical range for a residential ducted heat pump installation is $4,250 to $11,750.** A first central system starts here, from the ducts and air handler location up.

**Sweet Olive's typical range for a residential ducted heat pump replacement is $4,250 to $11,750.** Replacements and conversions from gas share it; the estimate states which parts of the house we keep.

We set your price after the site visit and write it into your estimate line by line: equipment, duct work, electrical work, the permit steps, removal and anything excluded. You can hold that estimate up against your planner result and see which lines moved, and why.

Not replacing anything yet? [Repairs](https://sweetolivenolaheatpumps.com/heat-pump-repair/) and [maintenance visits](https://sweetolivenolaheatpumps.com/heat-pump-maintenance/) are priced on their own, so they aren't part of the planner.

Flex runs leaving an attic air handler: whether these stay or go moves a budget more than anything else.

**Sweet Olive's typical range for a residential heat pump repair is $161 to $661.** The diagnostic visit and any major component are separate lines, priced once we know what failed.

**Sweet Olive's typical range for a residential heat pump maintenance visit is $70 to $200.** What the visit includes changes the price, and we list each check before we book it.

## What the planner can't see

Four things move a price that no set of answers can settle. Each one is a reason the visit comes before the estimate.

- Duct leakage and static pressure. Ducts that look fine can fail their tests, and ducts that look tired can pass them.
- What the panel can carry. A photo helps us prepare; the load the panel can take is worked out on site.
- The stand height a low lot needs. Flood elevation is set parcel by parcel, so we check it for your lot.
- Whether your address sits in a local historic district, which can change where the outdoor unit goes.

The planner also leaves out the permit fee, which the permit office for your address sets from the components in the job. When your estimate says we obtain the permit, the fee and the inspection are lines in it. Our [permits guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-permits/) lists the office for each part of the metro.

## Questions about the planner

### Why does the planner show part of the range instead of one figure?

A single figure would pretend to know what only the visit shows: whether the ducts pass their tests, what the panel can carry and how the copper lines have to run. The part of the range is honest about that. The typical jobs listed under your result show what scopes like yours are priced at, and the written estimate after the visit is the price for your house.

### Can I send you my planner answers?

Yes. Copy the link under your result and paste it into the message box of the estimate form, or keep it for the visit. The link holds only your answers. The planner itself sends nothing to us, and it never asks for a name or a phone number.

### Is a panel upgrade inside the planner's range?

No. New circuits and an outdoor disconnect for the heat pump sit inside the range, but a panel upgrade is a different job. When you tell the planner the panel is older or full, it lists the upgrade on a line of its own, and an electrician reviews the panel before that line is priced.
