# Heat Pump Installation Kenner LA | Ducted Replacement

> Heat pump installation, replacement and furnace-to-heat-pump swaps for Kenner homes, with every City of Kenner filing listed in your written estimate. Ask us.

URL: https://sweetolivenolaheatpumps.com/service-areas/kenner/

Tired of a gas furnace in winter and a separate air conditioner in summer? In Kenner we plan heat pump installations and conversions around the city's own permit office, your ducts and your panel, then set the whole job out in one written estimate.

Heat pump on an eighteen-inch stand beside a raised Kenner cottage.

## What brings Kenner homeowners to us

### The gas furnace is near the end

It still lights, but it is old and you would rather heat with the same system that cools. That changes the gas line, the flue and the wiring, not just the box.

### A slab house that never dries out

The thermostat reads 75 and the rooms still feel damp. Before anyone swaps the equipment, the size and the ducts need checking.

### The air conditioner died first

The outdoor unit failed in July and the furnace still works. This is the moment to decide whether one heat pump should do both jobs.

### You're buying or renovating in Kenner

You want the system planned before the walls close or the closing date arrives, with the city filings counted in the timeline.

Last updated: November 18, 2026

Your gas furnace still lights, but it is getting old, and the air conditioner beside it isn’t young either. You are wondering whether one heat pump could do both jobs, and what it takes to get there in a Kenner house.

[Sweet Olive](https://sweetolivenolaheatpumps.com/) installs ducted air-source heat pumps and converts gas-heated homes across Kenner and the rest of [our service area](https://sweetolivenolaheatpumps.com/service-areas/). Kenner runs its own permit office, separate from the parish, and a conversion can touch the mechanical, electrical and gas sides at once. So on the first visit we look at the furnace, the flue, the ducts, the panel and the outdoor spot together. Your written estimate names the equipment, the duct work, the wiring, any gas capping and every city filing, priced line by line.

If you have no central system yet, start with [new installation](https://sweetolivenolaheatpumps.com/heat-pump-installation/). If the furnace stays and only the cooling side failed, the [conversion page](https://sweetolivenolaheatpumps.com/heat-pump-conversion/) explains both routes, and an [inspection](https://sweetolivenolaheatpumps.com/heat-pump-inspection/) helps when you aren’t sure what is worth keeping.

## Inside a Rivertown gas-to-heat-pump conversion

An attic gas furnace near the end, a raised cottage near the river and three Kenner filings: how one house moved its heating onto the system that already cooled it.

- **Location**: Rivertown, Kenner
- **Home**: Raised single-story frame cottage, about 1,350 sq ft, two bedrooms
- **System**: Nominal 2.5-ton two-stage heat pump with a 5 kW heat strip
- **Removed**: Attic gas furnace, flue pipe and roof cap
- **Gas**: Furnace branch capped; water heater stays on gas
- **Outdoor unit**: 18-inch stand, 30-foot line set
- **Project price**: $9,550
- **Duration**: 3 working days

The house

### A gas furnace in the attic of a raised cottage

The cottage sat a few feet off the ground in Rivertown, about 1,350 square feet with two bedrooms. Heat came from a gas furnace lying in the attic with an air conditioning coil on its outlet, and the furnace was worn out. The owner wanted heating and cooling from one electric system. The water heater also ran on gas, so the gas service stayed.

The decision

### A heat pump, not a new furnace

We priced a dual-fuel setup that kept a new furnace as backup, and a straight conversion. The room-by-room load calculation supported a nominal two-and-a-half-ton, two-stage heat pump, and a 5 kW heat strip covered the coldest mornings, so the owner chose the conversion. The existing attic ducts passed the leakage test; the back bedroom got a jumper duct to the hall return.

- **Air handler**: on an attic platform, over a secondary drain pan
- **Supply runs**: dropping to ceiling registers
- **Central return**: in the hall ceiling
- **Jumper duct**: from a closed bedroom to the hall
- **Line set and drain**: along the outside wall
- **Outdoor unit**: on a raised stand, with its disconnect

The finished layout in section: the air handler on its attic platform over a secondary pan, ceiling registers, the hall return, a jumper duct and the outdoor unit on its stand.

The work

### Three filings and three working days

Kenner took the mechanical filing, and the gas and electrical work went on their own forms, so each trade filed before day one. On day one we recovered the refrigerant, a gas fitter capped the furnace branch at the tee, and we lowered the furnace through the hall opening. On day two we set the air handler on a new platform over a secondary pan with a float switch, pulled the flue pipe and sealed the roof where it had passed through. An electrician added the heat-strip circuit while we set the outdoor unit on an 18-inch stand.

The handover

### Backup heat checked before the city inspection

Day three covered the 30-foot line set brazed under nitrogen, the pressure test and the evacuation, then the charge, airflow and static pressure. We confirmed the heat strip and the defrost cycle, set the thermostat's stages, and left the readings with the owner. The aim was one system for summer and winter, with no open flame left in the attic.

## Kenner files its own permits

The city, not Jefferson Parish, handles the paperwork for a Kenner address.

### One city office, several forms

Kenner is an incorporated city, and its Inspection and Code Enforcement Department processes permit applications and coordinates inspections. The city keeps separate filing forms for electrical, gas, mechanical and plumbing work. A straight replacement is usually a mechanical filing. A gas-to-heat-pump conversion can add an electrical filing for a new circuit and a gas filing for capping the furnace branch. Your estimate lists each one and states who obtains it, and our [permit guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-permits/) compares the offices around New Orleans.

### The codes the city works from

Kenner lists the 2021 International Mechanical Code and the 2021 International Energy Conservation Code among the codes it follows, each with Louisiana’s state amendments. Those set the ground rules for the equipment, the duct sealing and the controls, and the city inspection checks the finished work against them.

Connections at an outdoor unit, one of the things a final inspection looks at.

| Part of the job | Filing | When it applies |
| --- | --- | --- |
| Equipment, line set and ducts | Mechanical | Every installation, replacement or conversion |
| New circuit or panel work | Electrical | When the heat pump or heat strip needs a new circuit |
| Capping a furnace gas branch | Gas | Gas-to-heat-pump conversions |
| Address east of Kenner | Jefferson Parish | [Metairie](https://sweetolivenolaheatpumps.com/service-areas/metairie/) and [River Ridge](https://sweetolivenolaheatpumps.com/service-areas/river-ridge/) addresses |

The filings a Kenner heat pump job can involve; your estimate shows which apply to your house.

## From the lake to the river: what changes the job

Kenner stretches from Lake Pontchartrain down to the Mississippi, and the houses change along the way.

7.62 in

Average June rainfall at the New Orleans airport in Kenner, from National Weather Service climate normals

Heavy summer rain and the humidity that follows it are why we treat moisture removal as part of the sizing, not an extra.

### North of Airline

Much of north Kenner was drained, filled and built out from the late 1950s onward. Where a house there sits on a slab, the air handler goes in a closet or up in the attic, and the ducts run overhead. Attic headroom, the size of the access opening and the return path from each bedroom decide most of the plan. Our [ductwork guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-ductwork/) shows what we test before reusing ducts.

Insulated supply runs leaving an attic plenum, where most slab-house ducts live.

A deep porch and a raised floor, a different starting point from a slab house.

### Rivertown and the older streets

Near the river, around Rivertown and Williams Boulevard, the streets are older and some houses stand on piers. There we keep the air handler and ducts out of the space under the floor and plan an attic layout instead, with a secondary drain pan and float switch under any cabinet above a ceiling.

### Where the outdoor unit sits

Wherever the house is, manufacturers set clearances around the coil and the service panel, and a low spot in the yard calls for a stand. We check the yard after rain, not just on a dry day, and the [placement guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-outdoor-unit-placement/) shows the options.

## Gas furnace, dual fuel or a full heat pump?

Three ways to handle a Kenner house that heats with gas today.

Full conversion

A heat pump heats and cools; a small electric heat strip covers cold snaps and defrost.

- One system to maintain
- Furnace branch capped, flue removed
- Panel must carry the heat strip

Dual fuel

A heat pump handles most of the year; a gas furnace takes over in the cold.

- Keeps a sound furnace working
- Gas service and flue stay
- Controls must manage both

If the furnace is worn out, a full conversion usually makes more sense; if it is sound, dual fuel can keep it working.

### Sizing comes before the decision

Either way, we run a room-by-room load calculation (ACCA Manual J) and size the heat pump from it, not from the old furnace or air conditioner nameplate. The heat strip is sized from the heating load, and the thermostat is set so the strip only runs when the heat pump needs help. The [gas furnace comparison](https://sweetolivenolaheatpumps.com/guide/heat-pump-vs-gas-furnace/) and [dual-fuel guide](https://sweetolivenolaheatpumps.com/guide/dual-fuel-heat-pump-systems/) go further.

### The panel decides some of it

A conversion adds electric load where gas used to carry the heating. We check the panel’s rating, open spaces and existing circuits on the first visit. An electrician adds any new circuit, and a panel upgrade, if one is needed, is its own line; the [electrical readiness guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-electrical-readiness/) explains the checks.

A wall thermostat that can call for each stage and for backup heat.

## What a Kenner heat pump costs

Kenner's own permit office doesn't change our range; the house and the scope do.

**Sweet Olive's typical range for a residential ducted heat pump installation is $4,250 to $11,750.** We set your price after the site visit and write it into your estimate line by line, with each Kenner filing for your address shown separately.

What moves a Kenner price

- **Equipment.** Capacity from the load calculation, single-stage or two-stage, and the heat strip size.
- **What comes out.** A gas furnace, its flue and roof cap, or an old air conditioner only.
- **The ducts.** Resealing a few joints, adding a jumper duct, or replacing runs that fail the test.
- **Electrical work.** Reusing a sound circuit, adding one, or a panel upgrade as a separate line.
- **Access and the outdoor spot.** Attic headroom, closet size, line-set length and a stand on a low lot.

The federal 25C credit no longer applies to equipment placed in service after December 31, 2025, according to IRS guidance. The [cost guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-cost/) breaks a price into its parts, and the [cost estimator](https://sweetolivenolaheatpumps.com/tools/heat-pump-cost-estimator/) gives a starting budget.

## How a Kenner job usually runs

Five steps, with the city's filings counted in from the start.

1. Send the address Kenner addresses go to the city's permit office, not the parish. Tell us what heats the house now and add photos of the furnace and the panel if you can.
2. We visit and measure Rooms, attic or closet, the duct runs, the panel, the gas line and the outdoor spot, with the ducts tested before we plan to reuse them.
3. Your written estimate Equipment, duct work, electrical work, any gas capping, the Kenner filings and exclusions, priced line by line.
4. Filings, then the work days Each trade's filing is handled as your estimate states, then the work days are booked with your floors protected.
5. Startup and city inspection Pressure test, evacuation, charge, airflow, backup heat and thermostat, with the readings left with you before the city inspection.

## Around Kenner

Permits: City of Kenner. Electric service: Entergy Louisiana, confirmed for your address.

Neighborhoods

- Rivertown
- Laketown
- Chateau Estates
- Lincoln Manor
- North Kenner

Landmarks

- Louis Armstrong New Orleans International Airport
- Pontchartrain Center
- Laketown

Main routes

- Williams Boulevard
- Veterans Memorial Boulevard
- Airline Drive
- Interstate 10
- Loyola Drive

Kenner and the communities around it that we serve. [Open the area in Google Maps](https://www.google.com/maps/search/?api=1&query=Kenner%2C%20Louisiana)

## Questions from Kenner

### Who issues the permit for a heat pump at a Kenner address?

The City of Kenner. Kenner is an incorporated city, so its Inspection and Code Enforcement Department handles permits instead of Jefferson Parish. The city keeps separate filing forms for mechanical, electrical, gas and plumbing work, so a conversion can involve more than one. Your written estimate lists each filing and states who obtains it.

### Do the extra Kenner filings for a gas conversion change the price?

Each filing shows up as its own line, along with the gas capping and the flue removal, so you can see what the conversion adds. Our typical range for a residential ducted heat pump installation is $4,250 to $11,750. A conversion usually lands inside it, depending on the ducts, the panel and access. We set the final figure after the visit.

### Can I keep my gas furnace and add a heat pump in Kenner?

Yes. A dual-fuel system pairs a heat pump with a gas furnace and lets the controls choose between them. It suits a house with a sound furnace and a gas service you want to keep. If the furnace is worn out, we price a straight conversion and a dual-fuel setup side by side so you can compare them.

### Do you work in all of Kenner, from Laketown down to Rivertown?

Kenner is in our service area from the lakefront to the river. When you contact us we confirm the address against the city line, because the eastern edge meets Metairie and River Ridge, where the parish handles permits, and the western edge meets St. Charles Parish. The office for your address goes into the estimate.

### Is a north Kenner slab house harder to fit a heat pump into than a raised one?

Not harder, just different. On a slab, the air handler usually sits in a closet or the attic and the ducts run overhead, so attic access and headroom decide a lot. A raised house adds the space underneath, which we keep equipment out of. We look at both on the first visit before choosing where everything goes.
