# Heat Pump Maintenance New Orleans | Both Modes Checked

> Heat pump maintenance for New Orleans homes, with the cooling side checked before summer and the heating side before the first cold snap. Ask for a visit.

URL: https://sweetolivenolaheatpumps.com/heat-pump-maintenance/

Your heat pump cools the house for most of the year, then has to heat it on the first cold morning after months of rest. We service both sides of the system, clear the drain that works hardest here, and leave you a record of every reading.

Technician rinsing the coil of a heat pump on a raised stand beside an Algiers Point cottage.

- Maintenance for ducted heat pumps in homes
- Cooling and heating sides both checked
- Typical range $70 to $200
- Every reading written on your record

Last updated: November 18, 2026

A heat pump here spends most of the year cooling and drying the house, then has to switch over and heat it on the first cold morning after months of rest. Maintenance is what keeps both of those jobs ready, and it matters most in the parts you never see: the coil, the drain and the switching that turns cooling into heat.

[Sweet Olive](https://sweetolivenolaheatpumps.com/) maintains ducted heat pumps in homes [across New Orleans](https://sweetolivenolaheatpumps.com/service-areas/). On a maintenance visit we clean the outdoor coil, flush the condensate drain, tighten and test the electrical parts, and run the system in cooling and heat. Every reading goes on a visit record you keep, so the next visit can compare against it.

If the system has already stopped cooling or heating, you need a [repair](https://sweetolivenolaheatpumps.com/heat-pump-repair/) visit instead. If you want an honest look at an unfamiliar system before deciding anything, a [heat pump inspection](https://sweetolivenolaheatpumps.com/heat-pump-inspection/) fits better.

## What a fall maintenance visit in Algiers Point looks like

A small system that had cooled all summer and not heated since spring: the checks that got it ready for the first cold morning.

Before

After

- **Location**: Algiers Point, New Orleans
- **Home**: Raised single-story cottage, about 1,300 sq ft, two bedrooms
- **System**: Nominal 2-ton heat pump, closet air handler with a 5 kW heat strip
- **Visit**: Fall service, before the heating season
- **Outdoor unit**: Beside the side steps, a vine reaching the coil
- **Heat checked**: Heat mode, defrost and the heat strip
- **Project price**: $165
- **Duration**: One visit, about 2 hours

The house

### A cooling season behind it

The house was a raised cottage in Algiers Point, about 1,300 square feet, with a two-ton heat pump, a closet air handler and a five-kilowatt heat strip. The system had cooled the house since May and hadn't run in heat mode since spring. A vine on the side fence had grown into one face of the outdoor coil.

The plan

### Heating checks, not just a filter

The fall visit put the weight on the heating side: the reversing valve, the defrost cycle and the heat strip. The cooling season had left its own work behind, so the condensate line and the outdoor coil got attention too. We booked it as one visit with the checks listed beforehand.

The visit record for one fall service: filter, coils, drain, electrical condition and the heating controls.

The visit

### Coil, drain, electrical, then heat

With power off at the disconnect, we cut the vine back from the cabinet, rinsed the coil from the inside out at low pressure and straightened bent fins. Inside, we fitted a new 16-by-25-inch filter, flushed the condensate line and tested the float switch. We tightened the electrical connections, read the capacitor and the amp draw of the compressor, fan and heat strip, then switched to heat and forced a defrost cycle to watch it change over and recover.

The record

### What the owner kept

Every reading went on the visit record, along with one note: the capacitor read at the low edge of its rating, worth checking again at the spring visit. The aim was a system that heated the first cold morning without the strip carrying the whole load.

## Why a heat pump needs two kinds of attention

One set of equipment does two jobs here, and each season wears on different parts.

Before the cooling season

Spring, ahead of the long, humid summer.

- Outdoor coil cleaned so it can shed heat
- Drain flushed and float switch tested before months of condensate
- Amp draws and capacitor checked before the heaviest load
- Airflow checked so the coil dries the air

Before the heating season

Fall, ahead of the first cold snap.

- Reversing valve switched to heat and checked
- Defrost cycle run and watched
- Heat strip amp draw measured
- Thermostat backup heat settings checked

One visit a year covers the side you rely on most. Two cover both.

### What the summer leaves behind

Through a long cooling season the indoor coil sends water down the condensate drain day after day, and algae and dust slowly narrow the line. The outdoor coil collects pollen, grass clippings and leaves. Neither shows until the drain overflows or the system starts losing ground on hot afternoons. Our [humidity guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-humidity-new-orleans/) explains why so much water comes off the coil here.

## What we check on a maintenance visit

The checks for your visit are listed before we book it. This is what each one is for.

| Check | What we do | Why it matters |
| --- | --- | --- |
| Outdoor coil | Clean, rinse from the inside out, straighten fins | A dirty coil can’t shed heat, so the system runs longer and harder |
| Condensate drain | Flush the line, clear the trap, test the float switch | A blocked drain is a common cause of water through a ceiling |
| Electrical | Tighten connections, read the capacitor, inspect the contactor | Loose or failing parts are behind many summer breakdowns |
| Amp draw | Measure compressor, fan, blower and heat strip | Readings that drift from the nameplate point to wear early |
| Heat mode | Switch over, check the reversing valve and a defrost cycle | The heating side sits idle for months before it is needed |
| Thermostat | Mode, stages and backup heat settings | A wrong setting can run the heat strip far more than needed |

Maintenance checks and why each one matters in a New Orleans home.

### Why the record matters

A single reading says little on its own. The same reading taken each visit, set beside the startup record, shows whether the capacitor is weakening, the compressor is drawing more current or the airflow is slipping. That gives you time to plan a repair instead of meeting it on the hottest day of the year.

The readings left at startup become the baseline each maintenance visit compares against.

## What you can do between visits

A few minutes a month keeps the system breathing and the drain clear.

Your monthly checks

- **The filter.** Look at it monthly in summer and change it when it looks grey.
- **The outdoor unit.** Keep plants, vines, leaves and stored items well back from the coil and the top of the cabinet.
- **The drain.** Know where the condensate line ends outside, and check it drips while the system cools.
- **The registers.** Keep supply and return grilles open and clear of furniture and rugs.
- **After a storm.** Look for debris in the unit and standing water around the pad before you switch it back on.

Check that the thermostat is set to the right mode when the seasons change.

The filter slot, the drain trap and the float switch at a closet air handler.

### What to leave for the visit

Leave the panels closed, the electrical parts alone and the indoor coil untouched. Never use a pressure washer on the outdoor coil; it folds the fins flat. Our [maintenance checklist](https://sweetolivenolaheatpumps.com/guide/heat-pump-maintenance-checklist/) has the full list, and the [warning signs guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-warning-signs/) covers what means you should call us before the next visit.

## What maintenance can and can't do

Regular service keeps a system close to how it was set up. It can't fix how it was set up.

### Efficiency ratings assume a clean, well-set system

The SEER2 and HSPF2 ratings on the label are measured with clean coils and correct airflow. A dirty coil, a clogged filter or a weak blower pulls real performance below the label, and the system runs longer cycles to make up for it. Keeping those parts clean is the part of efficiency maintenance can protect. Our [operating cost guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-operating-cost/) explains how the ratings and the bill connect.

### Limits worth knowing

Maintenance can’t promise a lower bill, a set number of years of life or a system that never breaks down. It also can’t correct an oversized system, leaky ducts or a return that is too small. If the record keeps pointing to the same problem, we tell you, and a [ductwork repair](https://sweetolivenolaheatpumps.com/heat-pump-ductwork-repair/) or a fresh look at the size may help more than another service.

## What a maintenance visit costs

The price follows what the visit includes and how easily we can reach the equipment.

**Sweet Olive's typical range for a residential heat pump maintenance visit is $70 to $200.** What the visit includes changes the price, and we list each check before we book it, so the figure on your estimate matches the work.

What moves a maintenance price

- **How many systems.** A second system is a second set of checks.
- **Where the air handler sits.** An attic platform takes longer to reach than a hall closet.
- **The coil cleaning.** A rinse is quick; a coil packed with dirt or a vine takes more time.
- **The filter.** A thin filter or a thicker media filter, supplied by you or by us.
- **Both seasons or one.** A fall visit adds the heating, defrost and backup heat checks.

A deep porch on a raised house, where the outdoor unit often sits close to the steps.

### When the visit finds a fault

If a check turns up a failing part, we explain it and price the repair before doing anything more. Repairs have their own range; see our [repair page](https://sweetolivenolaheatpumps.com/heat-pump-repair/) and the [cost guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-cost/) for how both are priced.

## What a maintenance visit includes

The checks for your visit are listed before we book it. A typical visit covers these.

- Filter checked and replaced, with a filter you supply or one we bring
- Outdoor coil cleaned and rinsed, fins straightened, debris and plants cleared from the cabinet
- Indoor coil, blower and cabinet inspected where they can be reached
- Condensate drain flushed, trap cleared and float switch tested
- Electrical connections tightened, capacitor read, contactor inspected
- Amp draw on the compressor, outdoor fan, blower and heat strip measured
- Thermostat checked for the right mode, stages and backup heat settings
- Cooling and heat mode run, with a defrost cycle checked before winter
- A visit record with the readings and anything to watch

## A maintenance visit, an inspection or a repair?

Three visits that can look alike from the driveway. Each has a different job.

*Maintenance, inspection and repair visits compared*

| Visit | When to book it | What it does | What you get |
| --- | --- | --- | --- |
| Maintenance | Before the cooling season, and before the heating season | Cleans, tightens, flushes and tests a system that is working | A serviced system and a record of its readings |
| Inspection | Before buying a house, after a storm or when you want an honest look | Reviews and measures the system without servicing it | Written findings and next steps |
| Repair | When something has stopped working | Finds the fault and fixes it | A working system and a record of what was replaced |

If the system is running and you want it to keep running, book maintenance. If you want to know where it stands first, book an inspection.

## How a maintenance visit runs

Five stops, usually in a single visit.

1. Book the visit Tell us how many systems, where the air handler sits and when it was last serviced. We list the checks and book a time.
2. Outside first Power off, the coil cleaned and rinsed, the electrical connections and the capacitor checked.
3. Then inside The filter, the blower, the coil we can reach, the drain, the pan and the float switch.
4. Run both modes Cooling, heat and the backup heat, with amp draws measured and a defrost cycle checked before winter.
5. Your record Every reading on a visit record you keep, with anything worth watching before the next visit.

## Questions we hear about this work

### How often should a heat pump be serviced in New Orleans?

At least once a year, before the cooling season, because summer is when the system works hardest here. A heat pump also heats, so a second visit before the first cold snap checks the reversing valve, the defrost cycle and the backup heat. Two visits a year cover both modes; one visit covers the side you rely on most.

### How often should I change the filter?

It depends on the filter and the house. A thin one-inch filter in a home with pets or ongoing work may need changing every month in summer; a thicker media filter can last several months. Check it monthly at first and replace it when it looks grey. A clogged filter cuts airflow and can freeze the coil.

### Can I clean the outdoor unit myself?

You can keep it clear. Cut back plants and vines, rake leaves away from the base and rinse light dust off the coil with a garden hose, never a pressure washer, with the power off at the disconnect. Leave the panels, the electrical parts and the indoor coil to the maintenance visit.

### Does a maintenance visit include cleaning the ducts?

No. A maintenance visit services the equipment and looks at the duct connections we can reach at the air handler. If we see loose joints, crushed runs or signs of leakage, we note them on the record. Repairing ducts is separate work, covered on our ductwork repair page.

### Does a brand new heat pump need maintenance?

Yes. A new system still collects dirt on its coils, still sends water down its drain all summer, and still has electrical connections that can loosen. The first visits also give you a baseline. Readings close to the startup record show the system is holding up, and readings that drift tell us where to look.
