# Furnace to Heat Pump Conversion New Orleans

> Converting a gas furnace and central air to one ducted heat pump in a New Orleans home, with ducts, wiring, backup heat and the gas line planned. Ask us.

URL: https://sweetolivenolaheatpumps.com/heat-pump-conversion/

A gas furnace in the attic or a closet, a separate air conditioner outside, and a wish to run the house on one system? We look at your ducts, your panel and what else uses gas, then plan a heat pump conversion, or a pairing with the furnace you keep, in one written estimate.

New air handler in a hall closet with the removed gas furnace on a hand truck in the hallway.

- Gas furnace to ducted heat pump
- Backup heat sized from your heating load
- Typical range $4,250 to $11,750
- Gas line and flue planned in the estimate

Last updated: November 18, 2026

You have a gas furnace in the attic or a hall closet, an air conditioner outside, and two systems to service, two sets of parts to fail and a gas appliance in the house. A heat pump can do both jobs with one outdoor unit and one indoor cabinet, but the change touches the ducts, the panel and the gas line, so it has to be planned before anything comes out.

[Sweet Olive](https://sweetolivenolaheatpumps.com/) converts homes [across New Orleans](https://sweetolivenolaheatpumps.com/service-areas/) from a gas furnace and central air to a ducted air-source heat pump. On the first visit we measure the rooms for a load calculation, test the existing ducts, check the panel for the new air handler circuit, and look at the flue and everything else in the house that uses gas. Your written estimate then sets out the conversion, and a pairing with your furnace where that fits, priced line by line.

If the house has a heat pump already, [heat pump replacement](https://sweetolivenolaheatpumps.com/heat-pump-replacement/) covers that job. If it has no central system at all, start with [heat pump installation](https://sweetolivenolaheatpumps.com/heat-pump-installation/).

## A typical Broadmoor furnace to heat pump conversion

A gas furnace in the attic, an air conditioner outside and an owner who wanted one system: how the conversion was planned around what stayed.

Before

After

- **Location**: Broadmoor, New Orleans
- **Home**: Raised single-story home, about 1,850 sq ft, three bedrooms
- **System**: Nominal 3-ton two-stage heat pump with an attic air handler, replacing an attic gas furnace and a central air conditioner
- **Backup heat**: Electric heat strip sized from the heating load
- **Gas and flue**: Furnace branch capped by a gas fitter; flue removed and roof patched
- **Line set**: 30 feet, new
- **Project price**: $10,400
- **Duration**: 3 working days

The house

### Two systems sharing one set of ducts

The house was a raised, single-story home in Broadmoor, about 1,850 square feet with three bedrooms. A horizontal gas furnace sat in the attic with a cooling coil on its outlet, a metal flue ran up through the roof, and a central air conditioner sat outside on a stand. The water heater and the range stayed on gas.

The decision

### A conversion, not a heat pump paired with the furnace

We priced both paths: a heat pump paired with the existing furnace for backup, or a full conversion. The furnace was past its best years and the owner wanted no fuel-burning appliance in the attic, so the plan was a full conversion. The load calculation supported a nominal three-ton, two-stage heat pump, with an electric heat strip sized from the heating load, not the largest the cabinet accepted.

- **Air handler**: on an attic platform, over a secondary drain pan
- **Supply runs**: dropping to ceiling registers
- **Central return**: in the hall ceiling
- **Jumper duct**: from a closed bedroom to the hall
- **Line set and drain**: along the outside wall
- **Outdoor unit**: on a raised stand, with its disconnect

The converted layout in section: the attic air handler where the furnace stood, the supply runs, the hall return and the outdoor unit on its stand.

The work

### Gas, flue and wiring in the right order

On day one a gas fitter capped the furnace branch at its tee, we pulled the furnace, coil and flue, and the roof opening was patched and flashed. The new air handler went on the same platform over a new secondary pan with a float switch, and the plenum transitions were rebuilt and sealed with mastic. On day two we set the outdoor unit on the existing stand and ran a new 30-foot line set while an electrician added the air handler circuit. Day three was the pressure test, evacuation, charge and startup.

The handover

### Both modes proven

At startup we ran cooling, then heat, then forced a defrost cycle and confirmed the heat strip came on only when the thermostat called for it. The readings stayed with the owner and the City inspection followed. The goal was one electric system that heated and cooled the house, with gas left only where the owner wanted it.

## Is a conversion right for your house?

Most houses with a furnace and central air can take a heat pump. The real question is whether a full conversion or a pairing with the furnace suits you better.

Pair a heat pump with the furnace

The heat pump heats most of the time and the furnace takes over on the coldest mornings.

- Keeps a sound furnace working
- No new heat strip circuit
- Two systems to service, and gas stays in the house

Full conversion

The heat pump heats, with an electric heat strip as backup.

- One system to service
- The furnace, its flue and the gas branch go
- A new circuit for the air handler and heat strip

Pairing suits a furnace with years left in it. A full conversion suits a furnace near its end, or a house where you want no gas appliance in the attic or closet.

### When to keep the furnace alone

If your air conditioner is new and the furnace is sound, there may be no reason to convert yet. An air conditioner can’t run in heat mode, so a conversion replaces it, and the timing often comes down to which unit wears out first. Our [heat pump vs gas furnace guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-vs-gas-furnace/) and [dual-fuel guide](https://sweetolivenolaheatpumps.com/guide/dual-fuel-heat-pump-systems/) compare the paths in depth.

## What we check on the furnace, the air conditioner and the ducts

A conversion reuses the house's air path, so we look closely at what the furnace and the old cooling coil leave behind.

- **The rooms.** Windows, sun, insulation and air leaks feed the load calculation for heating and cooling.
- **The furnace and coil.** Where they sit, how the plenums connect, and how much room a new air handler has.
- **The ducts.** Tested for leakage and static pressure before we plan to reuse them.
- **The flue and gas branch.** Where the flue leaves the house and where the furnace branch can be capped.
- **The panel.** Its rating, open spaces and what is already on it.
- **The outdoor spot.** Whether the air conditioner’s pad or stand can carry the heat pump.

- **Each room**: windows, sun and ceiling height for the load calculation
- **Attic opening**: headroom and joists
- **Return location**: where a central return can draw air
- **Electrical panel**: rating, open spaces and existing load
- **Outdoor spot**: footing and drainage
- **Thermostat**: on an inside wall

The first-visit stops on a three-bedroom plan, from the rooms and attic opening to the panel and the outdoor spot.

### Why the ducts matter more than you'd think

With a furnace, a leaky joint in a hot attic loses some very hot air and the furnace makes up for it fast. A heat pump delivers warm air at a lower temperature, often over longer runs, so the same leak or an undersized return costs it more comfort, and the registers can feel cool. We measure leakage and static pressure before we decide what to reuse, and our [ductwork repair](https://sweetolivenolaheatpumps.com/heat-pump-ductwork-repair/) page covers the fixes.

## Backup heat and the electrical side

A furnace brings its own heat. A heat pump needs a plan for cold mornings and defrost, and that plan has an electrical cost.

An air handler with its heat strip inside the cabinet, where a furnace once stood.

### Sizing the heat strip

Winters here are short, but cold snaps come, and the outdoor coil needs defrosting on damp mornings. An electric heat strip inside the air handler covers both. We size it from your heating load, not at the largest strip the cabinet accepts, because a bigger strip needs a bigger circuit and costs more to run. Our [sizing guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-sizing/) explains heating and cooling loads, and the [cold weather guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-cold-weather/) covers how the strip and the heat pump share the work.

### The new circuit

A gas furnace runs on a small circuit for its blower. An air handler with a heat strip needs a much larger dedicated one, and the heat pump outside needs its own. We check the panel’s rating and open spaces at the first visit; an electrician adds the circuits, and a panel upgrade, if needed, is a separate line. More in the [electrical readiness guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-electrical-readiness/).

### Controls that know the difference

A furnace thermostat calls for heat and nothing more. A heat pump thermostat has to manage the reversing valve, the compressor stages and when the strip may run, and in a paired system, when the furnace takes over. The [thermostat guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-thermostat-compatibility/) explains the wiring.

A thermostat that can call the heat pump, its stages and the backup heat separately.

## Gas, removal and installation, in order

A conversion has more trades and more steps than a replacement, so we sequence them carefully.

### Gas off and capped first

The gas supply to the furnace is shut off and a qualified gas fitter caps the branch, leaving the water heater, range or anything else that stays on gas connected. Your estimate states who does this work.

### Old equipment out

We recover the refrigerant from the air conditioner, then take out the outdoor unit, the furnace, its cooling coil and the flue. The flue opening in the roof or wall is closed as your estimate states.

### New equipment in

The air handler goes where the furnace stood, with the plenum transitions rebuilt and sealed with mastic and a secondary pan and float switch wherever it sits above a ceiling. The heat pump goes on its pad or stand, and the line set is brazed under nitrogen, pressure-tested and evacuated.

### Startup in both modes

We verify the charge, measure airflow and static pressure, test the drain, then run cooling, heat, a defrost cycle and the heat strip. The readings are left with you, and the permit inspection follows. The [heat pump vs gas furnace guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-vs-gas-furnace/) covers what changes in day-to-day use.

A heat pump on its pad, ready for the line set and wiring.

## What a conversion costs

A conversion is priced like a replacement, with the gas, flue and electrical work added as their own lines.

**Sweet Olive's typical range for a residential ducted heat pump replacement is $4,250 to $11,750.** A conversion sits in the same range, with the furnace removal, gas and flue work and the new circuit shown as separate lines. We set your price after the site visit and write it into your estimate line by line.

What moves a conversion price

- **Full conversion or pairing.** Pairing keeps the furnace and avoids the heat strip circuit.
- **Capacity and efficiency tier.** Two-stage and variable-speed equipment costs more.
- **The ducts.** Sound ducts keep it down; added returns or new runs raise it.
- **The electrical work.** A new circuit is routine; a panel upgrade is a separate line.
- **Gas and flue.** Capping the branch, removing the flue and closing the roof or wall opening.
- **Access.** An attic furnace is harder to remove and replace than one in a closet.

### Tax credits and rebates

The federal 25C credit no longer applies to equipment placed in service after December 31, 2025, according to IRS guidance. Utility rebates have their own rules on which projects qualify, so we check your account and the proposed equipment before counting any. See the [rebate guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-rebates/) and the [cost guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-cost/).

## What your conversion includes

Your written estimate names each of these for your house, and lists anything we leave out.

- The load calculation for cooling and heating, and the equipment choice that follows
- Removal of the furnace, its cooling coil and the outdoor air conditioner, with refrigerant recovered
- A matched outdoor heat pump and indoor air handler with an electric heat strip, or a heat pump paired with your furnace
- Plenum transitions rebuilt for the new cabinet and sealed with mastic
- A new or reused line set, as the estimate states, pressure-tested and evacuated
- The new air handler circuit, and any panel work, each as its own line
- The gas line capped at the furnace branch and the flue removed and closed, as the estimate states
- Condensate drain, secondary pan and float switch where the air handler sits above a ceiling
- A thermostat set up for heat pump stages, backup heat and defrost
- The permit and inspection steps for your address, and startup readings left with you

## Three ways to heat and cool with the ducts you have

Starting from a gas furnace and central air, these are the real choices.

*Keeping the furnace and air conditioner, pairing a heat pump with the furnace, and a full conversion compared*

| Option | What goes in | How it heats | What to plan for |
| --- | --- | --- | --- |
| Keep furnace and air conditioner | A new air conditioner, or nothing | Gas, as now | Combustion checks, venting and the gas appliance stay; no change in how the house heats |
| Heat pump paired with the furnace | A heat pump outside and a matched coil on the furnace | The heat pump most of the time, gas on the coldest mornings | Controls that hand off between the two, and the furnace still to service |
| Full conversion | A heat pump and an air handler with an electric heat strip | The heat pump, with the strip as backup | A new circuit for the air handler, the gas line capped and the flue removed |

When the furnace is near the end of its life, or you want the gas appliance out of the house, a full conversion makes sense. When the furnace is sound, pairing a heat pump with it can cost less now.

## How your conversion runs

Six stops from your first message to the day you take over the thermostat.

1. Tell us about the house Where the furnace sits, what else runs on gas, and how the house heats and cools now. Photos of the panel and both units help.
2. We visit and measure The rooms, the furnace and coil, the ducts, the panel, the flue and the outdoor spot.
3. Your written estimate The equipment, backup heat, electrical work, gas and flue work, permit steps and exclusions, priced line by line.
4. Permit and scheduling The permit is handled as your estimate states and the gas work is booked before the work days.
5. The work days Gas capped, old equipment out, air handler and ducts, then the outdoor unit, line set, drain and wiring.
6. Startup and handover Cooling, heat, defrost and backup heat proven, with the readings and a walk-through of the thermostat.

## Questions we hear about this work

### Can I keep my gas furnace as backup heat?

Yes, if it is in good condition. A heat pump can be paired with the furnace so the heat pump handles most of the heating and the furnace takes over on the coldest mornings. That needs a cooling coil matched to the heat pump and a thermostat that manages the changeover. The furnace still needs its own combustion checks and service.

### What happens to the gas line and the flue?

In a full conversion the gas branch to the furnace is capped, and the flue is removed and its opening in the roof or wall closed. Gas work is done by a qualified gas fitter. Your estimate states who caps the line, how the flue opening is closed and what stays connected, so nothing is left to guesswork.

### Will my gas bill go away after the conversion?

Only if nothing else in the house uses gas. A water heater, a range, a dryer or a fireplace keeps the account open, and most gas bills carry a monthly charge however little you use. Your heating moves to the electric bill, so that rises in winter while the gas bill falls.

### Does a heat pump heat the house as well as a gas furnace?

It heats differently. A furnace sends short bursts of hot air; a heat pump sends a longer, steadier stream of warm air, which can feel cooler at the register while the rooms reach the same temperature. On cold mornings and during defrost, the backup heat strip tops it up. Sizing and controls decide how comfortable it feels.

### Can I convert if my air conditioner is still fairly new?

You can, but the air conditioner can't simply become a heat pump. It has no reversing valve, so it can't run in heat mode, and the outdoor unit is replaced in a conversion. When the air conditioner is new and the furnace is sound, the timing often comes down to which one wears out first. We price the options so you can choose when.
