# What Electrical Requirements Does a Heat Pump Have?

> The circuits, disconnect, heat strip, panel capacity and control wiring a ducted heat pump needs, and what we check at your panel before equipment is chosen.

URL: https://sweetolivenolaheatpumps.com/guide/heat-pump-electrical-readiness/

The electrical checks that belong in a heat pump estimate, why the old breaker doesn't settle them, and where the electrician's work begins.

Technician testing the electrical compartment of an outdoor heat pump unit beside a raised Mid-City house.

Last updated: November 18, 2026

The short answer

A ducted heat pump needs a dedicated circuit for the outdoor unit, circuits for the air handler and its electric heat strip, a disconnect within sight of the outdoor unit, and control wiring for each stage. The nameplates set the wire and breaker sizes, and the panel has to carry the added load. An electrician runs new circuits.

Key takeaways

- The new equipment's nameplates set the circuits; the old breaker label doesn't.
- The heat strip often draws more current than the heat pump itself.
- An open breaker space isn't proof the panel can carry the load.
- A panel or service upgrade, when needed, is its own line in the estimate.
- Leave the panel cover on; a photo of the label is all we need before the visit.

The heat pump you choose sets the electrical work, not the breaker the old system used. A larger strip, a different outdoor unit or a move off gas heat can each change the circuits a house needs, and the panel has to carry all of it.

[Sweet Olive](https://sweetolivenolaheatpumps.com/) installs heat pumps across New Orleans and keeps the electrical work visible in every estimate. This guide covers what the equipment asks of your wiring, how we check the panel, and where an electrician’s work begins. For how the heat strip is sized, see our [sizing guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-sizing/).

## What the nameplate tells the electrician

Each indoor and outdoor unit carries a label with the figures its circuit is sized from.

| Nameplate figure | What it means | What it sets |
| --- | --- | --- |
| Voltage and phase | The supply the unit is built for, such as 208/230 volts, single phase | Which circuit type it needs |
| Minimum circuit ampacity | The smallest current the circuit’s conductors must carry | Wire size |
| Maximum overcurrent protection | The largest breaker or fuse allowed | Breaker size |
| Compressor and fan ratings | The current each motor draws | Starting and running load |
| Heat strip kilowatts and circuits | The strip’s size and how many circuits it needs | Air handler circuits and panel load |

The electrical figures on a heat pump's nameplate and what each one sets.

### Why the old breaker doesn't settle it

The old system’s breaker was sized for the old system’s nameplate. A new outdoor unit can call for a different wire or breaker, and the air handler’s figures change with the strip size. The circuit has to match the new equipment’s installation instructions and the code that applies to your building. The [components guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-components/) shows where each unit sits.

An outdoor unit on its pad; its nameplate sits on the cabinet near the electrical connections.

## The heat strip and the panel

Backup heat is usually the largest electrical load in the system, which makes its size a panel question.

| Heat strip size | Current at 240 volts |
| --- | --- |
| 5 kW | About 21 amps |
| 8 kW | About 33 amps |
| 10 kW | About 42 amps |
| 15 kW | About 63 amps |

Current drawn by common electric heat strip sizes at 240 volts, from kilowatts divided by volts.

The heat strip sits inside the air handler, wired from its own circuit or circuits.

### Sized to the heating load, not the cabinet

An air handler often accepts several strip sizes. The largest isn’t the safest: it adds load to the panel and runs hotter than the house needs. We size the strip from the heating figure in the load calculation, then check that the panel can carry it with everything else. A heat pump with a sound gas furnace as backup avoids the strip altogether, as our [dual-fuel guide](https://sweetolivenolaheatpumps.com/guide/dual-fuel-heat-pump-systems/) explains.

What we check at the panel

- **The rating** of the panel and the service feeding it.
- **Open spaces** for the new breakers, including any two-pole breakers the strip needs.
- **What is already on it:** range, dryer, water heater, pool pump or a car charger.
- **Condition:** scorched breakers, double-tapped connections or signs of water.

A raised house with its outdoor unit by the steps; the circuit runs from the panel inside to the disconnect here.

## Leave the panel to the electrician

Electrical work on a heat pump installation is planned in the estimate and done by an electrician, not by you.

What to send us instead

Don’t remove the panel cover or test anything live. A photo of the label inside the panel door and a wide photo of the breakers with the door open is enough for us to prepare the visit. We look at the rest in person.

The panel can carry it

New circuits fit the rating and the existing load.

- Circuits and disconnect are lines in the estimate
- An electrician runs them during the work days
- The inspection covers the finished wiring

The panel can't

The load check or condition says it needs work.

- A panel or service upgrade is a separate line
- It may involve the utility and its own permit
- We explain it before you decide on the system

Either way, you see the electrical scope before you commit.

## The disconnect, the outdoor side and the controls

Past the panel, three more pieces finish the electrical work.

### The outdoor disconnect

A disconnect within sight of the outdoor unit lets it be shut off safely for service. It sits on the wall or the stand, clear of the coil’s airflow. Where a unit stands on a raised stand because water collects after heavy rain, the disconnect and wiring go up with it. FEMA guidance notes that heating and cooling equipment isn’t designed to withstand flooding, and elevation needs depend on the parcel.

### Control wiring

The thermostat cable carries the low-voltage calls for each stage, the reversing valve, the fan and the backup heat. A two-stage or variable-speed system needs more conductors than an old single-stage cable may have, and some systems use their own communicating control. Our [thermostat compatibility guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-thermostat-compatibility/) covers the checks.

An outdoor unit on its pad; the disconnect sits on the wall or stand beside a unit like this.

## Moving off gas, and commercial buildings

Two cases add electrical work beyond a straight replacement.

| Situation | What changes electrically | Where to read more |
| --- | --- | --- |
| Gas furnace to an all-electric heat pump | The air handler and heat strip need new circuits that the furnace never used | [Furnace to heat pump conversion](https://sweetolivenolaheatpumps.com/heat-pump-conversion/) |
| Gas furnace kept as backup | The furnace keeps its circuit; the heat pump adds the outdoor circuit and controls | [Heat pump or gas furnace](https://sweetolivenolaheatpumps.com/guide/heat-pump-vs-gas-furnace/) |
| Commercial building | Voltage and phase can differ, and the scope is set per project | [Commercial heat pumps](https://sweetolivenolaheatpumps.com/commercial-heat-pumps/) |

Electrical changes in a gas-to-heat-pump conversion and in commercial work.

Whatever the building, the estimate lists the new circuits, the disconnect and any panel work as lines of their own, and the [installation process guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-installation-process/) shows when the electrical work happens.

## Three more questions

### Can a new heat pump reuse the old air conditioner's circuit?

Sometimes, if the wire and breaker match what the new outdoor unit's nameplate calls for and the wiring is in good condition. A higher-capacity unit, a different model or a change from a gas furnace to an electric heat strip can each call for different circuits. We read the new nameplate against the existing circuit before deciding, and the estimate says which circuits stay and which are new.

### Why does the outdoor unit need a disconnect if the breaker is inside?

So the unit can be shut off where the work happens. A disconnect within sight of the outdoor unit lets a technician cut power at the unit and see that it stays off, instead of relying on a breaker in another room that someone could switch back on. It is part of the circuit the electrician installs, and a line in the estimate.

### Why does the heat strip need its own breaker?

Because it draws a large current of its own whenever it runs, often more than the outdoor unit. Larger strips are split into sections, each with its own breaker, so the conductors and protection match the load. The air handler's nameplate lists the circuits the strip size requires.
