# Commercial Heat Pump Installation New Orleans

> New ducted heat pumps for New Orleans shops, offices, restaurants and small buildings, planned around how the space is used and priced per project. Ask us.

URL: https://sweetolivenolaheatpumps.com/commercial-heat-pumps/

Fitting out a storefront, an office or a small building with no working system? We plan ducted heat pumps around how the space is used, where the equipment can sit and how it will be reached for service, then price the whole project in one written estimate.

Two heat pump outdoor units on steel stands on the flat roof of a Freret storefront.

- Ducted heat pumps for shops, offices and small buildings
- Sized from how the space is used
- Priced per project
- Written estimate after the walk-through

Last updated: November 18, 2026

A new tenant space, a storefront whose old equipment is long gone, or a small building going up: each needs heating and cooling planned around how the space will be used. A café with ovens, an office full of screens and a shop with a west-facing window put very different loads on the same floor area.

[Sweet Olive](https://sweetolivenolaheatpumps.com/) installs ducted air-source heat pumps in shops, offices, restaurants and small multi-tenant buildings [across New Orleans](https://sweetolivenolaheatpumps.com/service-areas/). We walk the space, the roof or yard and the electrical room, ask how the business runs, and price the equipment, ducts, wiring, controls and permit steps as one written estimate.

If the building already has heat pumps that are failing, [commercial heat pump replacement](https://sweetolivenolaheatpumps.com/commercial-heat-pump-replacement/) is the closer fit. If it runs on gas furnaces or another type of system today, start with a [commercial retrofit](https://sweetolivenolaheatpumps.com/commercial-heat-pump-retrofit/). For a house, see [residential installation](https://sweetolivenolaheatpumps.com/heat-pump-installation/).

## Inside a Freret storefront installation

An empty shell, a west-facing shop window and a café open next door: the first system we put into a small Freret office.

During the work

After

- **Location**: Freret, New Orleans
- **Property**: One-story brick storefront, about 1,600 sq ft, fitted out as a design office
- **System**: Two ducted heat pumps, nominal 3-ton and 2-ton
- **Ductwork**: Sheet-metal trunks, 11 supply diffusers and 2 returns above a lay-in ceiling
- **Outdoor units**: Two units on steel stands on the flat roof
- **Controls**: Two scheduled thermostats, one per zone
- **Project price**: $26,450
- **Duration**: 6 working days

The space

### A bare shell behind a big window

The building was a one-story brick storefront on the Freret corridor, about 1,600 square feet, being fitted out as a design office for eight people. The old equipment had come out years before, so the shell had wiring stubs, a tall west-facing shop window and a new lay-in ceiling going up at ten feet. A café shared the party wall and the flat roof, and it stayed open throughout the work.

The decision

### Two zones instead of one big unit

The load calculation split the space in two. The glass-fronted studio carried most of the afternoon heat; the back conference room, kitchenette and restroom carried far less. A nominal three-ton system served the front and a two-ton system served the back, so each ran long, steady cycles on its own load. One larger system was the alternative we priced, but it meant overcooling the back rooms every time the studio called for cooling.

The startup record each system passed before the office took over its thermostats.

The work

### Ceiling first, then the roof

On days one and two we hung both horizontal air handlers above the ceiling grid, each over a secondary pan with a float switch, and ran sheet-metal trunks to eleven diffusers and two returns. An outside-air duct with a balancing damper tied into the studio return, sized on the permit drawing. On day three we lifted both outdoor units to the roof from the rear lot on a rented material lift and set them on steel stands, with both line sets dropping through one flashed penetration. Day four belonged to the electrician's two new circuits and disconnects.

The handover

### Readings, schedules and a clean ceiling

Day five was the nitrogen pressure test, evacuation to a micron reading and the charge. On day six we set airflow at each diffuser, programmed both thermostats to the office's hours and tested the drains and float switches. The ceiling tiles went back clean, the roof was swept, and the startup readings and equipment records went to the owner ahead of the City inspection. The aim was a studio that held temperature through a sunny afternoon without chilling the back rooms.

## Is a new system the right job for your space?

A new installation fits when the space has no working system, or when a fit-out changes the rooms so much that the old layout no longer makes sense.

Signs a new system fits

- **A shell or gutted space.** The old equipment is gone or unusable, and the ceiling is open for a new duct route.
- **A change of use.** A shop floor becoming an office or a restaurant changes the people, equipment and hours the system serves.
- **Room for the equipment.** Space for air handlers above a ceiling or in a closet, and a spot outside for the outdoor units.
- **An electrical supply with room for new circuits,** or a clear way to add capacity.

A meeting table by the storefront glass, where afternoon sun adds to the cooling load.

### When it's a different job

Ductless mini splits are a different kind of system that we don’t install, so a space with no route for ducts at all points that way. Kitchen hood exhaust and make-up air are designed separately from the heating and cooling, though the two have to be planned together because the hood pulls air the heat pumps must replace and condition.

## What we ask about the building and the business

A commercial load starts with the people, the equipment and the hours, not the square footage.

| What we ask | Why it matters |
| --- | --- |
| How many people use the space, and when | People add heat and moisture; a dining room at lunch carries a very different load from the same room at three |
| What runs inside | Ovens, coffee machines, printers, servers and display lighting all add heat the system has to remove |
| Hours and days of use | The controls are scheduled around them, and they decide when the work itself can happen |
| Glass and sun | Storefront glass facing west can drive the afternoon load at the front of the space |
| Ceiling, roof and closets | Where air handlers, ducts and outdoor units can sit, and how they are reached for service |
| Electrical room | The supply, the open spaces in the panel and the route for new circuits |
| Landlord and building rules | Roof access, approved equipment spots, permitted work hours and who signs off |

What we ask at the walk-through, and why each answer changes the design.

### Fresh air is its own question

A heat pump moves heat and removes moisture from the air already in the space; it doesn’t bring outdoor air in. Occupied commercial spaces need outdoor air for ventilation, in an amount set by how the space is used, so we plan an outside-air connection or a separate ventilation path alongside the heat pumps. Your estimate states which one your space gets.

## Sizing, ducts and controls for a business

Each step sets up the next one, so we take them in order.

### From the load to the equipment

The load calculation adds up heat through the glass, walls and roof, plus the people, equipment and lights, zone by zone. That decides capacity, and whether one system or several fits better. Splitting a sunny front room from quiet back rooms lets each system run long, steady cycles on its own load, which is what keeps a humid space dry. The size of the unit next door is never the test. Our [sizing guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-sizing/) explains the method.

### From the equipment to the ducts

Capacity sets the airflow, and the airflow sets the duct sizes. We lay out trunks and branches to each diffuser, give every closed room a way back to a return, and seal every connection with mastic. Where an air handler sits above a finished ceiling, a secondary drain pan with a float switch goes under it. The [ductwork guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-ductwork/) covers sizing and leakage.

A horizontal air handler on a platform, with insulated round supply runs leaving the plenum.

A wall control that can run the space's schedule and each stage of the system.

### Controls that follow the business

A commercial thermostat runs on a schedule: comfortable while the doors are open, set back overnight and on closed days. We wire it for the equipment’s stages and the backup heat and program it to your hours, so the heat strip runs only when the heat pump can’t keep up. Our [thermostat guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-thermostat-compatibility/) covers compatibility.

### Startup proves the design

The new piping is brazed under nitrogen, held under nitrogen pressure and evacuated to a micron reading before refrigerant goes in. At startup we measure airflow and static pressure, set each blower for its ducts, verify the charge, test the drains and float switches and confirm the controls. Those readings become the baseline every later [maintenance visit](https://sweetolivenolaheatpumps.com/commercial-heat-pump-maintenance/) compares against.

## Working around a business that's open

Commercial installations are planned around access, neighbours and the hours the building is in use.

### Roof, yard and the route to them

Outdoor units go on a flat roof, in a rear yard or along a side passage, and each needs the clearances the manufacturer sets and a firm, level support. Getting them there can mean a rented material lift from a rear lot, a roof hatch or a long carry down a passage. We choose the equipment and the lifting method to fit the route. The [placement guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-outdoor-unit-placement/) shows the options.

### Neighbours, tenants and the landlord

Where a neighbouring tenant stays open, we agree when the noisy and dusty steps happen, where materials are staged and which entrance we use. The landlord’s roof rules and any approval steps go on the schedule before equipment is ordered.

An outdoor unit on a raised pad, with its disconnect and insulated line set beside it.

### Permits for commercial work

The City of New Orleans requires a mechanical permit to install heating and cooling equipment, and Jefferson Parish and the cities around us run their own offices. A change of use or new outside-air ductwork can bring a mechanical drawing into the permit. Your written estimate states who obtains the permit, and our [permit guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-permits/) walks through each office.

## How we price a commercial installation

The price comes from the project, so it comes after the walk-through.

**We price commercial heat pump work per project, from the equipment, the building and the access the work needs.** We set your price after the site visit and write it into your estimate line by line, so you can see what each part of the project adds.

What moves a commercial price

- **Number and size of systems.** One system or several zones, and the efficiency tier of each.
- **Ductwork.** New trunks and diffusers through an open ceiling cost less to run than work around finished ceilings.
- **The outdoor unit route.** A roof lift, a hatch or a long carry, plus stands and roof flashing.
- **Electrical supply.** New circuits are routine; added service capacity is a separate line.
- **Ventilation.** An outside-air connection with its damper and balancing.
- **Drawings, permits and hours.** What the permit office asks for, and work the building limits to certain hours.

### Comparing two proposals

Two commercial proposals can sit far apart because one leaves out the lift, the roof flashing or the outside air. Ask each to name the same items before you compare totals. The [electrical readiness guide](https://sweetolivenolaheatpumps.com/guide/heat-pump-electrical-readiness/) explains what the circuits and supply involve, and [commercial maintenance](https://sweetolivenolaheatpumps.com/commercial-heat-pump-maintenance/) keeps the new equipment on record once it runs.

## What a commercial installation includes

Your written estimate lists each of these for your space, and names anything we leave out.

- A walk-through of the space, the ceiling, the roof or yard and the electrical room
- The load calculation, and the number and size of systems that follow from it
- Outdoor heat pumps, matched indoor air handlers and the backup heat the load calls for
- Supply and return ductwork, diffusers and grilles, sealed at every connection
- An outside-air connection or a stated ventilation path, as the estimate lists
- Insulated copper line sets, with roof or wall penetrations flashed and sealed
- Condensate drains, plus a secondary pan and float switch under any air handler above a ceiling
- Stands or pads, disconnects and the new circuits the equipment needs
- Scheduled thermostats wired for each system's stages and backup heat
- The permit and inspection steps for the address
- Startup readings and equipment records for the building file

## One system or several for a commercial space

The same floor area can be served three ways. We install the first two.

*One larger ducted heat pump, several zoned ducted heat pumps and ductless units compared*

| Option | How it serves the space | Where it fits | What to plan for |
| --- | --- | --- | --- |
| One larger ducted heat pump | One outdoor unit, one air handler and one thermostat for the whole space | An open space with even sun and use from front to back | Rooms with lighter loads can overcool while the busiest room calls for cooling |
| Two or more ducted heat pumps by zone | Each zone gets its own system and thermostat | A sunny front and quiet back rooms, or spaces with different hours | More outdoor units to place, more circuits and more line sets |
| Ductless units | A wall or ceiling head in each room, piped to an outdoor unit | Spaces with no route for ducts at all | A different type of system that we don't install |

When the space has room above the ceiling or in a closet, ducted heat pumps zoned by load keep busy and quiet rooms comfortable at the same time. If the walk-through finds no duct route, we tell you before you commit.

## How a commercial installation runs

Six stops from your first message to the handover of the controls.

1. Tell us about the space The address, what the space is used for, its hours, any plans or photos, and who coordinates the property.
2. Walk-through We walk the space, the ceiling, the roof or yard and the electrical room, and ask how the business runs.
3. Your written estimate Systems, ducts, ventilation, electrical work, the lifting method, permit steps and exclusions, priced line by line.
4. Approvals and scheduling Landlord sign-off and the permit come first, then the equipment order and work days set around the business.
5. The work days Air handlers and ducts, then the outdoor units and line sets, then the wiring and controls.
6. Startup and handover Pressure test, evacuation, charge, airflow, drains and schedules, with the readings for the property file.

## Questions we hear about this work

### Do commercial heat pump jobs need drawings for the permit?

Some do and some don't. A change of use, new ductwork through a building or a new outside-air connection can bring a mechanical drawing into the permit, while a simple system in an existing layout may not need one. We confirm what the permit office for your address asks for, and the estimate says who prepares any drawing and who obtains the permit.

### Can a shop or office stay open while the system goes in?

Often part of it can. Work above a ceiling or on the roof can run while a neighbouring space trades, and a zoned job can bring one area on line at a time. Dusty and noisy steps go to the hours you choose where the building allows it. The work plan in your estimate shows which areas are affected on which days.

### Does a heat pump bring fresh air into a business?

No. A heat pump cools, heats and dries the air already inside; it does not bring in outdoor air by itself. Occupied commercial spaces need outdoor air for ventilation, and how much depends on how the space is used. We plan an outside-air connection or a separate ventilation path alongside the heat pumps and name it in the estimate.

### Should the outdoor units go on the roof or on the ground?

It depends on the building. A flat roof keeps units out of the way and away from standing water, but it needs a safe way up for the lift and for every service visit. A rear yard or side passage is easier to reach but has to keep the manufacturer's clearances. Landlord rules and any historic district review can settle it.

### What does a commercial installation estimate spell out?

The number and size of systems, the ductwork and diffusers, the ventilation, the electrical work, how the equipment gets to the roof or yard, the permit steps, the work days and what each area loses during them, and the exclusions. Each part is priced on its own line, so you can compare proposals item by item.
